How to replace tact-switch under a button for Denon DJ SC-2000?
How to replace tact-switch under a button for Denon DJ SC-2000?
Like many other people that have the issue a button isn’t responding anymore, or partly, depending where you push on a specific button, this is a guide how-to replace a so-called tact-switch, which is causing this issue.
Afterwards, your button reacts like brand-new!
Damage: 4 euro.
http://i65.tinypic.com/jzbpxc.jpg
Tools used:
http://i64.tinypic.com/125qedu.jpg
http://i67.tinypic.com/2hxbqyb.jpg
Part ordered:
http://i66.tinypic.com/x4i06x.jpg
Bottom-side (4 screws):
http://i66.tinypic.com/2mr8ml5.jpg
Top-side (5 screws):
http://i68.tinypic.com/29o4chs.jpg
Left & Right-side (2x 2 screws):
http://i66.tinypic.com/97r6nd.jpg
Face-side (6 screws):
http://i63.tinypic.com/2wgsjuf.jpg
Pull off the pitchfader knob:
http://i63.tinypic.com/211uvwp.jpg
Tilt up the unit out of its back-plate:
http://i67.tinypic.com/2chmc5w.jpg
Flip the unit (20 screws):
http://i66.tinypic.com/23r5ufr.jpg
Flip the unit / Pull off the rotary knobs firmly (6 knobs):
http://i63.tinypic.com/2w3qmwk.jpg
Tilt up the faceplate & unmount the nuts & bolts (6x 6 nuts/bolts):
http://i66.tinypic.com/263yfwl.jpg
http://i67.tinypic.com/wk1cgy.jpg
http://i65.tinypic.com/2cy451j.jpg
http://i63.tinypic.com/i41h6s.jpg
If you did good, you end up with all the loose parts like this:
http://i68.tinypic.com/nfl0te.jpg
Flip the unit & unsolder the jogwheel-wire:
http://i68.tinypic.com/2434zyw.jpg
http://i63.tinypic.com/11havdu.jpg
Flip the motherboard carefully, so the connector-cable won’t get damaged:
http://i66.tinypic.com/oa4v3l.jpg
http://i68.tinypic.com/2yv439l.jpg
Unsolder the defect tact-switch, by pushing the solder-end towards 1 pin & a little screwdriver against the other side of the pin, until it lets loose:
http://i63.tinypic.com/2poy7nm.jpg
Do this for all 4 pins:
http://i68.tinypic.com/16hs3f7.jpg
Now solder the new tact-switch into place:
NOTE: Try if the button works after soldering, by plugging in the USB-cable & start up your DJ-software, to see if the buttons reacts.
http://i68.tinypic.com/17wcvq.jpg
If not, like I had here, now’s the time to delete some solder, by removing redundant solder, making the solder hot with your solder-device & quickly scrape it away with your little screw-driver.
http://i66.tinypic.com/50fm0y.jpg
Try it works now… If so, follow this how-to in reverse & assemble the unit. Done!
If the pics are not showing after a year orso, here's a PDF-download of this guide:
https://mega.nz/#!UV5GBRxD!8gwMbj8V0...gfXO21CSoCrLq0