VCI-100 Needs firmware upgrade in Newport Beach Orange county area.
Results 1 to 4 of 4
  1. #1
    Tech Convert
    Join Date
    Jun 2008
    Posts
    19

    Default VCI-100 Needs firmware upgrade in Newport Beach Orange county area.

    Anyone have a firmware kit?

    How can I tell if I have version 1.4?

  2. #2
    Newbie
    Join Date
    Dec 2012
    Posts
    2

    Default

    Quote Originally Posted by Golden Ears View Post
    Anyone have a firmware kit?

    How can I tell if I have version 1.4?
    The vci-100 firmware kits are back in stock.

    Which firmware version does your VCi-100 have?
    Version 1.1
    the firmware with the "ramp up problem"


    the jog wheel touch sensor turns off when the wheel stops turning, not when you release your finger.

    Version 1.2
    -VCI-100's with a green sticker on the back are firmware version 1.2
    - this version solved the ramp up problem but still has several bugs including
    * the fourth FX buttons send out the same midi message as the right headphone cue button.


    Version 1.3
    The firmware found in all VCi-100SE controllers that was designed by Ean Golden.

    You can tell if you have 1.3 by following these steps.

    1) connect your vci-100 to a computer but dont start traktor.

    2) Click the button that is at the top right hand corner of the left jog wheel (its next to the filter knob for deck A).

    3) If this button's light toggles on and off then you have 1.3 (the same button on the right deck will not toggle on and off.

    Here are a few of the changes made in 1.3

    general improvements:

    * Eliminated the problem where the 4th FX buttons trigger other buttons (cue)
    * added midi in functionality to the loop buttons
    * added a note on to the jog wheel in scroll mode

    performance:

    * turned the filter knobs into double knobs (0-127 on the left and right side)
    * added a "freeze function" to the bottom of each fader and top of the fx knobs. this sends out a 127 message only at the end of the movement
    * added inverted messages to the faders (this allows an effect to be turned on by turning the fader down- not possible otherwise)
    * added unique values to the FX buttons (these were used for direct FX selection- now added in Traktor Pro)

  3. #3
    Tech Convert Remoire's Avatar
    Join Date
    Feb 2013
    Posts
    13

    Default

    Quote Originally Posted by virus1200 View Post
    The vci-100 firmware kits are back in stock.
    Am I reading this wrong or did they really sell out in less than a few weeks? Crazy!

    I'm new around here and was about to buy a normal VCI100 to mod/upgrade...


    Do they come back in stock often?

    Ty!

  4. #4
    Tech Convert
    Join Date
    Jun 2008
    Posts
    19

    Default The firmware thing should be made a sticky

    Quote Originally Posted by virus1200 View Post
    The vci-100 firmware kits are back in stock.

    Which firmware version does your VCi-100 have?
    Version 1.1
    the firmware with the "ramp up problem"


    the jog wheel touch sensor turns off when the wheel stops turning, not when you release your finger.

    Version 1.2
    -VCI-100's with a green sticker on the back are firmware version 1.2
    - this version solved the ramp up problem but still has several bugs including
    * the fourth FX buttons send out the same midi message as the right headphone cue button.


    Version 1.3
    The firmware found in all VCi-100SE controllers that was designed by Ean Golden.

    You can tell if you have 1.3 by following these steps.

    1) connect your vci-100 to a computer but dont start traktor.

    2) Click the button that is at the top right hand corner of the left jog wheel (its next to the filter knob for deck A).

    3) If this button's light toggles on and off then you have 1.3 (the same button on the right deck will not toggle on and off.

    Here are a few of the changes made in 1.3

    general improvements:

    * Eliminated the problem where the 4th FX buttons trigger other buttons (cue)
    * added midi in functionality to the loop buttons
    * added a note on to the jog wheel in scroll mode

    performance:

    * turned the filter knobs into double knobs (0-127 on the left and right side)
    * added a "freeze function" to the bottom of each fader and top of the fx knobs. this sends out a 127 message only at the end of the movement
    * added inverted messages to the faders (this allows an effect to be turned on by turning the fader down- not possible otherwise)
    * added unique values to the FX buttons (these were used for direct FX selection- now added in Traktor Pro)
    this was incredibly helpful, now I can find out my firware version.

    Which firmware works with traktor pro 2?

    Also what is the way to tell if you have 1.4 ??? Dicso mode?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •