Printable View
Is there a way so that those Track Selection boutons dont react like you said, like changing the midi message of the 8 device control knobs and boutons? Because I had other plans for these.
Do you know how I could use Bome so that the Track Control knobs react to the parameters of the Fx panels into traktor?
Thanks:)
The TRACK SELECTION buttons do provide an output. I am using them to change FX panel mode from adv/chained for each effect. Potentially, you could map every bank with the same controls, so changing banks would not affect what the knobs/buttons are used for in the DEVICE CONTROL section. You may run into takeover problems as each bank's knobs would have a different value, and would require soft-takeover or cause jumps in direct mode. In my first mapping, I simply stated that you must keep the MASTER track selection button selected and not do any bank switching. You could also simply use a modifier with the CLIP STOP buttons to get another layer of buttons without messing with the TRACK SELECTION buttons.
I haven't used Bomes and can't help you with that. There should be plenty of posts on DJTT and Bome's forums to guide you.
Misa... thanks alot!!!:D
this looks like a great mapping misa wish i had the money for an apc40 but i'm going ot have to go for an apc 20 and map it for 2 decks in traktor not 4. would your mapping tsi still work on the 20 just without the right hand side of the controller. as the 20 does not have it????
Misa
I'm trying to download the tsi file but it doesnt work...
EDIT: ok it works now!! :)
Thanks!! :)
ok, I have a noob question here:
I imported the tsi file in traktor, but I can't get it to load my apc40...
can you tell me the exact steps to follow? and the midi input/output config, because traktor can't detect my apc40...
The apc40 is working well in Ableton.
thanks for your help!
I cant get this to work :(???????
Hey i have the apc20 and i am looking for the apc20 misa .tsi Does anyone have this?? please i need
Thanks
Omar
Hey did you ever end up making the mpk25 .tsi??
Top work there Misa.
Just purchased an APC40 on the road to trying to get an APC80 under my belt........
I will be coming back here once the delivery is made........
You are a true star for sharing your hard work.
Fleater
nice i chek this
thank you sooooo much, i will build off this to suit APC40 only controll (for now) and will learn from your work. thanks again!
this controller has gotten extremely popular, even I have one for TP2 =p
thats what im using it for! Awesome!
hey guys, so i just dove into the world of mapping for traktor as I just got the APC40 and i am having a little trouble. I already have 4 decks with play and loop and pitchbend and a volume fader for each deck. i also got the xfader to work between chanels. i feel like an idiot because i can't find the command for activating the headphone cue on each deck. i need to figure out how i can moniter different than the house mix and i'm hoping you all could show me some midi mapping forum love. haha.
-shaggy dupes
Great Job Misa..
Do you happen to have a JPG or PDF image of all the mapped buttons and knobs?
It will greatly be appreciated.
Thanks
maybe Im doing something wrong but I put my apc40 into "dumb mode" by opening ableton and making sure the apc40 is working in there, then closing out of it and opening traktor.
when I do this I lose LED rings around the "device control" section and the 9 banks of encoders I also lose access to... any help?
@Shaggy Dupes have you checked out the Traktor Command Finder on TraktorBible.com?
http://traktorbible.com/en/t2_commandfinder.aspx
Just mouse over the different GUI elements and it will show you all the corresponding mapping commands. It doesn't explain them in detail (That's what the book is for) but it will give you a rough idea of what it is and how you could use it. Hope this helps and if you really want to get into detail on MIDI mapping in Traktor I would buy the Bible it is THE resource when it comes to Traktor and Mapping.
Done a bit of research. Now for the basic noob question that goes far and solves all my problems when answered:
If you use the regular mode (not dumb mode) can you map the "Track Selection" buttons?
What exactly does selecting them change? I used the "learn" button to check other threads I've read. Each row has the same notes/cc, but each column resides on a different channel. Would they change if I selected a different Track Selection?
What does "bank" actually mean? Does it mean that like in Ableton selecting a Track Selection button makes all the midi notes/cc's of all other buttons in columns 1-8 different than if another Track Selection button were pressed (like in Ableton)?
Ppl have used the term bank for different things in probably incorrect/colloquial ways..I want to know the real truth.
FRUSTRATION!!!!!!
Gahh, I don't even know how to explain this without being confusing. It's a simple small fact which solves everything, but I haven't been able to figure it out because I haven't found one post to be completely clear with all terminology described and comprehensive...frustration is beinding me. I spent all of yesterday doing a Mixtrack mapping.
P.S. What exactly is dumb mode. Does it mean that all hardware midi maps are wiped clean? Resulting in a fully unmapped device?
My questions have been answered in this thread, for those interested: http://www.djtechtools.com/forum/sho...752#post379752