The what is new in Traktor Pro 2 thread

[Yep.]

I found that you can control post fader effects like the echo freeze with the main eq instead of the limited control you used to get in S4 and Pro.

[GeekGod]

I found that you can control post fader effects like the echo freeze with the main eq instead of the limited control you used to get in S4 and Pro.

Interesting. Does auto gain now work with post fader effects now? I was mapping a button to lower the volume fader a bit but would rather use autogain for that.

[DjNecro]

It seems as though I am going to have to re-analyse my tracks... the cues are there, the grid is there, but the preview wave doesnt load if i dont re-analyze...

Is this just me?

[GeekGod]

It seems as though I am going to have to re-analyse my tracks... the cues are there, the grid is there, but the preview wave doesnt load if i dont re-analyze...

Is this just me?

Not seeing that here. Just loaded a set that I have been working on this week and all of the cue points and the preview wave shows up OK. However it took a moment before the preview wave rendered.. Noticeably longer than the older version but could not have been longer than 5 seconds or so.

[exokinetic]

*CONFIRMED*


Send Monitor State is FIXED in Windows!!!

On top of this, I also experience NO distortion/pops/crackles, even when spamming the LED's faster than I would EVER do when I actually play.


This testing was done with:

Audio 2 DJ

AND

Audio 8 DJ

(Tried with both)

NI Kontrol X1 (custom mapping with two "Send Monitor State" triggers)

Behringer DDM4000 (with mapped LED feedback)

2x Denon DN-SC2000 (modified mapping with heavy LED feedback)


I did the testing with a track playing through a low pass filter down to around 80hz, so the pops/crackles/distortion that happens in the upper frequency spectrum would be much easier to hear.


And it sounds CLEAN.


I am so stoked. I used to have to set both my Denon controllers to NOT receive MIDI data from traktor, so that the LED issue was partially fixed (I just turned off the LED feedback basically, but could still use the controller).

I could also COMPLETELY crash out traktor, and sometimes even cause a BSOD through button press spamming. If I pressed enough buttons fast enough, and spammed the LED's enough, everything would come CRASHING to a halt...


Now it is utter perfection.


<3 NI

[mistertuckshop]

I found that you can control post fader effects like the echo freeze with the main eq instead of the limited control you used to get in S4 and Pro.

I thought you could do that in Traktor Pro... not S4, but I think that was confirmed to be unintended?

[DjNecro]

Not seeing that here. Just loaded a set that I have been working on this week and all of the cue points and the preview wave shows up OK. However it took a moment before the preview wave rendered.. Noticeably longer than the older version but could not have been longer than 5 seconds or so.

When I run a consistency check on my collection it comes back saying every single track is 'missing stripe'... whatever that means...

I've also had to double the asio4all buffer from 512 to 1024 in order to eliminate pops and cracks...

(Intel Core 2 Quad @ 2.4gig, 4gig ram, 1tb drive, win xp pro)

[Ashigari]

beat sync = the old sync
temp sync = only adjusts BPM so you have to beatmatch (nudge it into sync)

at least that's how I understand it

edit: oh and I can now route all 4 channels through my audio 2 dj, sample decks for poor djs :P

[paulmac]

ok probly a dum question, just hooked my s4 up2 my macbook and the light abouve the snap button is flashing away, is the driver not set up correct? its not the usb light flasshing its the triangle next that and i cant see anything mentioned about this in the manual\

[rdej47]

It seems as though I am going to have to re-analyse my tracks... the cues are there, the grid is there, but the preview wave doesnt load if i dont re-analyze...

Is this just me?

The reason your stripes are Missing is because traktor has to reanalyze the files to create the new colored waveform. Your grids and cues will all be there it just needs to update the waveform to the new color version