The Official TSP2 Bug and other stuff that should work the way i want it to thread.

[itajeN]

The waveform not rendering behind the playhead is a bit irritating.

It's not that bad. Lol.

[psylozen]

You could do that with Bomes, psy...

Yeah, was thinking that it might be time to familiarize myself /w bomes... But NI also seems to be really good about adding missing midi commands.

[VanGogo]

Ok my turn.

I use software focus not hardware, and everytime I start up TPro2 I have to select software focus again. Didn't happen in S4.

Yes I'm runnin under admin and windows 7 64-bit.

[photojojo]

Ok my turn.

I use software focus not hardware, and everytime I start up TPro2 I have to select software focus again. Didn't happen in S4.

Yes I'm runnin under admin and windows 7 64-bit.

I do to, that kind sucks!

[IrishBlaggard]

Ok my turn.

I use software focus not hardware, and everytime I start up TPro2 I have to select software focus again. Didn't happen in S4.

Yes I'm runnin under admin and windows 7 64-bit.

i never noticed that, i must test...

but heres the NOOB question, what does each one do,whats the difference ?

[Audeo]

Ok I looked for it but didn't find it yet or perhaps I overlooked it.. but when syncin tracks (I only have buttons and knobs, no faders) I can't get the tempo to stay..

Example:

Deck A plays at 128bpm. Load up a track in Deck B, this track is native 130bpm.
I press sync. Deck B goes to 128 BUT I can only play it quantized because sync is on.
As soon as I press sync again, disabling it, Deck B automatically reverts back to 130bpm instead of stayin on 128bpm..

How do I fix this?

[padi_04]

i never noticed that, i must test...

but heres the NOOB question, what does each one do,whats the difference ?

hard: follows S4 deck focus
soft: regular

[IrishBlaggard]

hard: follows S4 deck focus
soft: regular

in english for a stupid person like me paddy...

or would i better off to RTFM ?

[Scott Michael]

First post here fellas and I would be extremely happy if someone could help me out. I had TPS2 w/ Audio 10 and my cdj's running for a few days now and everything seemed to be okay. Today I pulled out my TT's and decided to give the time code vinyl a try and this is where everything hit the fan.

I hooked up my TT's via the manual and I couldn't get a time code signal to appear in TSP2. I re-ran the set up wizard selecting my X1 as a controller, then selecting the Audio 10 as my sound card and the deck configuration I want after that. Still I was not getting a time code signal.

Trying to isolate the problem I shut down Traktor to decided to run audio through the Audio 10 to verify it was working. The Direct Thru worked for ouputs 3/4 however the output signal of 5 was soft, about -6db and 6 showing normal. All other outputs functioned normal. I think this is a whole seperate issue beside the time code.

I decided to give up on getting the time code working with the TT's and set my CDJ's back up. Everything plugged in and routed properly, I now cannot get TSP2 to recognize the time code from the cd's either.

Also the FX section is doing some weird stuff as well. None of the paramaters are listed and the Kontrol X1 will not function properly.

Just to make sure I'm setting everything up properly here is what i have done.

CDJ 1000 RCA output to Audio 10 Input, Audio 10 Output to DJM 800 Input (Line)

The Audio 10 is configured for "Line" on the 2 outputs (3/4)(5/6). Direct Thru is not checked since i want to send a time code signal vrs. playing a regular cd.

Ive attached a PIC so you can see the FX section software error.


Thanks for all your help in advance.

PC Specs:

E8500 3.2 ghz
4gb DDR3 Ram
Clean instal Windows 7 64 bit

Scott

[padi_04]

in english for a stupid person like me paddy...

or would i better off to RTFM ?

My irish isn't that good, so RTFM

Disclaimer: not saying irish is stupid

Edit: TFM doesn't explain too much really

Deck Focus: Select control of the visual Deck Focus from the following menu: Software: Enable Software control of Deck Focus.
Hardware: Enable Hardware control of Deck Focus.
None: Disable Deck Focus.

Hardware: Displays the 2 decks focused on the S4 controller (what you see over the controller faders). No clue if it works with other hardware.
Software: you can map or click a single deck to change the focus of a particular parameter. Say you map the play button to follow focus, that parameter will only affect the selected deck, changing the focus to another deck will now make the play button affect the new selection.