Gemini Cntrl-7 and Traktor Help.........

[gothsoul3990]

There are some glitches when im playing a song , im using asio and i think its cuz of that or maybe the sound card in cntrl7 is fucked up. what u say guys?
and thanks for that mapping guys, really helpful! thanks a lott

[Stewe]

There are some glitches when im playing a song , im using asio and i think its cuz of that or maybe the sound card in cntrl7 is fucked up. what u say guys?
and thanks for that mapping guys, really helpful! thanks a lott

Try fixing sound glitches by decreasing audio latency from audio device panel.

[alejotejada]

I had the same problem.. I did as Stewe said and also increased the buffer size for each device in the asio control panel and the sound is not muffled and messed up anymore.

I'm having a problem with the mapper and the jog wheels. The search function is not working, jog wheels are working for the pitch bend but not for searching. Anyone has experienced this problem? I'm using the map with traktor version 2.5, everything else is working. I did a test with version 2.2 and the jog wheels work properly but the FX section doesn't. With version 2.5 the jog wheels have problems when using search function, i keep the search button pressed while using the jog but it doesn't search.

[Stewe]

There was issue with jog search, thanks for noticing it. Please report every bug that you find. Also ideas are welcome! There are few free buttons to be mapped and if there is a way to engage those 12 LED's on each side (sample on in VDJ) to map something cool there. As long if they work in midi ofc, but it couldn't surprise me if those LED's are controlled in VDJ in hid like some of buttons are. Is there any way to read this LED's code in midi?

Updated: http://www.traktorbible.com/freaks/m...ew.aspx?id=463

I would really like to see this mapping an action

[alejotejada]

Hey Stewe! Thanks a lot for the update. I just tested it and the search function on the right deck works perfectly, but not on the left deck. Left deck's jog is still not working when searching.
I also have an idea to map the buttons below the sync buttons, the ones that say "sampler play", it would be cool to map them for the headphone cue buttons

[Stewe]

Those jogwheels are sending two different CC values, one when nudge (no press) and other when press and turn (scratching).

Nudge deck A = CC.018
Scratch deck A = CC.016

Point is. If you tried to search with shift+nudge (018) and I mapped it to shift+scratch (016) you couldn't be able to, right? I got both codes mapped in now so it should make no difference which part of jog is used for searching.

http://www.traktorbible.com/freaks/m...ew.aspx?id=463

Headphone Cue is already mapped in mate. Check diagram with controls and you will notice headphone label under your load buttons. Just use "mixer shift" and press load buttons. Please tell me if it work properly since nobody confirmed it yet.

[alejotejada]

You're right i didn't notice the headphone cue buttons were already mapped, thanks!! they work perfectly. But i'm still getting problems when searching with the jog wheel on the right deck. I made a mistake when explaining in the last message.. The jog wheel that searches with no problems is the jog on the deck A, that will be the jog of the left deck. The jog on deck B is not working the same way as the other. On deck A i press the search button while spinning the jog and it searches with no problems, but when i try to do the same with deck's B jog it doesn't search. I also pressed the scratch button instead of the search button, tried without pressing any button as well but it doesn't work

[Stewe]

If issue is present again then could be shift isn't working at all and Seek Position can't be activated because of incorrect midi note for this button.

Gemini CTRL-7.zip

[alejotejada]

Thanks a lot Stewe!! the search function is working on both decks now.
Another thing that i noticed with this mapping is that the only shift button that seems to work is the one under the browser button. The ones under the search button on both decks are not working.
Also, when trying to work with the FX3 portion, the button works but not every single time. Sometimes i need to close traktor and open it again for this FX3 shifted button to work.

[Stewe]

Also, when trying to work with the FX3 portion, the button works but not every single time. Sometimes i need to close traktor and open it again for this FX3 shifted button to work.

Knob 3 button is basically toggling modifier and it works or it doesn't. No middle though. Maybe LED output isn't properly set so it's causing this issue. Does LED lite up correctly and does it happen on both sides?