4 Banks mapping

[0Notice]

Still can't get the bloody thing to work I have my 8 Buttons mapped to specify values and to turn on looping. Now I have each of those buttons mapped to change the modifier directly 0-7. Any help on mapping the LED output. Please.

[Stewe]

You can follow order in controller range from my original post.

[0Notice]

You can follow order in controller range from my original post.

Wont work. Closest thing Ive got is just a light up when its on the correct value. What should I use as my out message like, Loop Size select and Set or the Modifier?

[Stewe]

Loop size / Controller ange

/32 = 0
/16 = 1
/8 = 2
/4 = 3
/2 = 4
1 = 5
2 = 6
4 = 7
8 = 8
16 = 9
32 = 10

[0Notice]

Loop size / Controller ange

/32 = 0
/16 = 1
/8 = 2
/4 = 3
/2 = 4
1 = 5
2 = 6
4 = 7
8 = 8
16 = 9
32 = 10

Ive got that to work but I want it to be only lit up if its in an active loop.

[Stewe]

Ive got that to work but I want it to be only lit up if its in an active loop.

Ste modifier condition 'Is in Active loop' to all LED outputs

[0Notice]

Still cant get it to work could you give me the full run through, Add in > (something) > Then the modifiers. This is driving me bloody insane. Thanks.

[Stewe]

That should be easy as assigning modifier condition 'Is in Active loop' to Loop Size Selector LED outputs.

Add out > Deck Common > Loop > Loop Size Selector
modifier condition - Is in Active loop (will lite only if loop engaged)
controller range - 0-0 (example for /32)

This is off topic here btw.

[tekkon]

Still cant get it to work could you give me the full run through, Add in > (something) > Then the modifiers. This is driving me bloody insane. Thanks.

Dont know if you ever got this working but this is how I have it setup.

Untitled 1.pdf


I know it doesnt make sense to have the modifier on the "Loop Active ON" switch but it seems to work better (could just be my controller). I am running TSP 2.6 with a Novation launchpad, External mixer and a remote zero for FX. My LED Output range is actually 10-19 (red - orange) but the default 0-127 (ON/OFF) should be fine or change it as you need it. I had this running with 4 decks a while back. I just might set that up again.

Invert and Blend are unchecked for all parameters.

Good luck.

[trabz]

Simply need more options on your controller or wish to push your Traktor mapping potential to the max? This is a mapping technique you've been looking for.

Add in modifier #1
Type of Controller = Button
Interaction mode = Direct
Value = 1
Add out modifier #1
Controller range - 1 to 1

Add in modifier #1
Type of Controller = Button
Interaction mode = Direct
Value = 2
Add out modifier #1
Controller range - 2 to 2

Add in modifier #1
Type of Controller = Button
Interaction mode = Direct
Value = 3
Add out modifier #1
Controller range - 3 to 3

Add in modifier #1
Type of Controller = Button
Interaction mode = Direct
Value = 4
Add out modifier #1
Controller range - 4 to 4

Attachment 11160

Hey Stewe

I've been mapping all the commands for my Bank1, adding a condition M1=1 (I started all over again with your tsi file)

When I switch to Bank2, the commands from Bank1 don't work (so far so good), but the lights still remain.

Example;

Bank1: cue (in) M1=1
cue (out) / midi range 95/95 /// M1=1

Bank2: only browser on (in) M1=2
only browser on (out) / midi range 3/124 /// M1=2

When I press Bank2 the browser button lights up and works perfectly. When I switch back to bank1 the browser button is still there lighten up although uneffective.

Can't figure what I've been doing wrong