Traktor 1.2 not working with maschine? Anyone else have problems?

[DvlsAdvct]

Right. I meant try changing the interaction mode in the TSI. So instead of the type being Absolute KNob/Fader, changing it to relative Knob and seeing what happens.

It's a way until someone hopefully comes along who has a Maschine. Also, checking the Native Instrument forums can't hurt

[iancairns01iancairns01]

changed it to realtive and reduced the sensitivity and what i get now is that it slowly goes from 0 to 5 then skips thourh to 127 and flickers all over the place. And aswell when i rotate button 2 on FX 1 it also restarts the song in deck A, i don't even know how that could happen.

[iancairns01iancairns01]

Bump, if any maschine users are reading this i'm still baffled as to how to fix this and would love to know how you are getting on with your maschine

[gfocus]

Hey, I'm using the Maschine to control Traktor. I don't have any problems with it but I mapped it myself. I'm pretty sure the problem lies somewhere within the tsi. I'll have a look at the stock tsi and see if I can reproduce this behavior when I'm at home...

[iancairns01iancairns01]

Hey, I'm using the Maschine to control Traktor. I don't have any problems with it but I mapped it myself. I'm pretty sure the problem lies somewhere within the tsi. I'll have a look at the stock tsi and see if I can reproduce this behavior when I'm at home...

that'd be brilliant, thanks for that i'm not getting much luck with help on the native instrument forums at the moment!

[gfocus]

I'm sorry, I couldn't reproduce your errors. I loaded NI's stock tsi and everything works as described in the pdf.

I can change the loop size in both decks with the knobs. Of course, when I turned the knob the first time after initializing Traktor, it jumped straight to any value because Traktor didn't seem to know the current state of the knob. But this isn't unusual and happens immediately after you start Traktor and turn knobs the first time.

Did you know that you can adjust the knob resolution and range in the controller editor? Maybe you should try tweaking the settings there.

Do you use other MIDI controllers simultaneously?

[iancairns01iancairns01]

I'm sorry, I couldn't reproduce your errors. I loaded NI's stock tsi and everything works as described in the pdf.

I can change the loop size in both decks with the knobs. Of course, when I turned the knob the first time after initializing Traktor, it jumped straight to any value because Traktor didn't seem to know the current state of the knob. But this isn't unusual and happens immediately after you start Traktor and turn knobs the first time.

Did you know that you can adjust the knob resolution and range in the controller editor? Maybe you should try tweaking the settings there.

Do you use other MIDI controllers simultaneously?

The Thing is i think the first time i used the maschine, everything worked ok, i was hoping to use the controller simultaneously with the nanokontrol. I think i had both them working at one point but not sure. Could this be a problem? Also i think i mentioned elsewhere that the .tsi that i upload is in my Native Instruments from traktor and is possibly an old tsi file. What is the point of the controller editor? I used it like the Video shows but where does it save? Do you get yours working fine with traktor 1.2? The knobs work fine when i'm using maschine standalone but are you saying that i might have messed with them in the editor? I've looked in the editor and can't see where to change this tho?

[gfocus]

To adjust the knob settings:
click on the knob in the controller editor
on the right side of the window click "Assign"

I tested NI's tsi with TPRo 1.2.2 so that won't be the problem. Your "Chained FX on + CUP" issue looks like a clash between the nano's assignment and Maschine...

[iancairns01iancairns01]

To adjust the knob settings:
click on the knob in the controller editor
on the right side of the window click "Assign"

I tested NI's tsi with TPRo 1.2.2 so that won't be the problem. Your "Chained FX on + CUP" issue looks like a clash between the nano's assignment and Maschine...

What should i adjust them to?

Their settings are exactly the same as the knobs that are working correctly.
I also deleted the nanokontrol tsi so why is it still clashing with the maschine tsi, and also what do you use to EQ with maschine then?

Again thanks so much for all the help, its greatly appreciated!

[gfocus]

Unfortunately I haven't been that much of a help for you. Just shooting in the dark...

When you say you deleted the nano tsi, do you mean
*) you literally deleted the file from your hd
*) or actually delete the controller from the settings in traktor?

I use both the Maschine and the VCI and have the mixer and transport controls mapped to the vci. I use the Maschine for 4 Deck HotCues, Loops, BeatJumps, for FX slot 3&4.