Gemini Cntrl-7 and Traktor Help.........

[Stewe]

sorry i can't test the .tsi now :s

It should work I guess, I only need to map control over effects and that's it. Thank you for pic your assistance on creating this one with all your testing. I wish you luck with your new peace of gear!

Happy mixing

[xhaze]

Thanks i finally bought American audio vsm4 it should works great! can't wait!

[psimonius]

Hey Stewe,

Thanks for your efforts on this. I've seen the great work you've done here and on the NI forums. I've just bought the CNTRL-7 and want to use it with Traktor so if you're still working on this TSI, I may be able to help. Let me know.

[Stewe]

Hey Stewe,

Thanks for your efforts on this. I've seen the great work you've done here and on the NI forums. I've just bought the CNTRL-7 and want to use it with Traktor so if you're still working on this TSI, I may be able to help. Let me know.

Hey Psimonius, nice to see reply on this

Have you downloaded it at NI forum? If so, can you please tell me is there any issues with mapping at this moment?Yes, still working on it and I would like to get all controls to work properly before posting it on downloading sites. Here is diagram and tsi:

ctrl_7 layout.JPG

ctrl-7.tsi

[psimonius]

Hey Stewe, sorry for the lack of reply, my computer had died on me. All fixed now. First impressions are good. Basic functions are tight.

My only grumble - and its minor - is that the low/mid/high knobs don't fully kill. Is it possible to tweak that?

I've added a couple of my own bits. On the front panel (you can't see it on the pic above) are monitor headphone volume, monitor mix and X-Fader curve controls. Screenshot below if you want to add to your .tsi.

monitor.jpg

[psimonius]

Ah the pic has shrunk. They are:

Monitor Vol Adjust / In / Global / Direct / Ch01.CC.042
Monitor Mix Adjust / In / Global / Direct / Ch01.CC.040
Curve Adjust / In / Global / Direct / Ch01.CC031

[Stewe]

Hi Psimonius, good to see you again!

low/mid/high knobs don't fully kill. Is it possible to tweak that?monitor.jpg

I watched review about EQ knobs aren't the best when it comes to full cut of frequencies so I added EQ kill feature to mixer section. Check Mixer "shift" button. While holding it, twist any EQ's knob and it should engage kill button for corresponding knob. After that, while you twist it again (no shift) EQ kill is off. Have you tested every bit of controls?

See diagram, everything labeled with "slash" is shift related.

Too bad that it can't be properly mapped all buttons as I mentioned in this thread, it could be nice double deck focus mapping with jog FX modes as much as sample LEDs. Speaking if I got one myself to start setup for that ctrl-7 ultimate mapping.

Thanks for reminder I know xhaze sent me controls for front panel also, I'll add it tomorrow and update. This mapping is still under construction and you can notice that three buttons are not mapped. How about some echo out? Can you tell how's drama acting with jog sensitivity? Was it too slow? Anything specified you would like to add?

[Stewe]

Update to mapping:

Front panel controls added.

http://www.traktorbible.com/freaks/m...ew.aspx?id=463

[alejotejada]

Update to mapping:

Front panel controls added.

http://maps.djtechtools.com/mappings/521
http://www.traktorbible.com/freaks/m...ew.aspx?id=463

Hey Stewe!

Thank you very much for your work. I own this controller and tested the mapper. Everything seems to be working for me except the FX portion.. I can help testing this mapper, just let me know..

[Stewe]

Hey Stewe!

Thank you very much for your work. I own this controller and tested the mapper. Everything seems to be working for me except the FX portion.. I can help testing this mapper, just let me know..

It's funny that another user told me that everything else works except of jogwhells and faders... I would be very grateful if you can come up with quick video that will demo this issues for me.

Thanks