To perform this trick, Traktor need to be set to four FX units since this supercombo use FX units #2 and 3.
First press:
-Set Fx units #2 and 3 to group mode
-Set M1=1
-Loading Beatmasher to unit #2 and Transpose Stretch to unit 3
-Set dry/wet to max-1.000 at both FX units
-Set Beatmasher amount to 0.600
-Set Transpose Stretch amount to 1.000 (ready)
-Beatmasher on (direct 1)
Second press:
-Set M1=2
-Set Beatmasher amount to 0.800
Third press:
-Set M1=3
-Set Beatmasher ammount to 0.900
Fourth press and hold:
-Set M1=4
-Set Beatmasher amount to 1.000
-Decrease Transpose amount (sweep)
-Transpose on (hold)
After fourth press and hold of the button (till sweep end) when button is released both of effects go off and modifier value jump back to zero (M1=0) so this combo is ready for new cycle.
If someone is interested to give this a try, after importing .tsi file twice from BIG IMPORT button, just map all of commands from mapping to one single button on your MIDI controller.
I inported your tsi, and it gives in Mapped to: Ch01.Note.C 1
I try to hit the button “Learn” in Traktor but it doesn’t work.
I use the S4 and F1
I’m new at tsi files and try to analyse the tsi of Scamo.
can you give more info how to do this please.
Beatmasher+Transpose supercombo single button (this is your mapping)
Control Assingment Mode Mapped to Cond1 Cond2 Type Inter Assingment Options
Modifier 1 Global Inc Mapped to ?? — ---- Button Inc Global —
Modifier 1 Global Hold Mapped to ?? M1-4 ---- Button Hold Global 0
Dry/Wet Adjust (FX Unit) FX Unit 2 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 2 1,000
Dry/Wet Adjust (FX Unit) FX Unit 3 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 3 1,000
Knob 3 FX Unit 2 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 2 0,600
Knob 3 FX Unit 2 Direct Mapped to ?? M1-1 ---- Button Direct FX Unit 2 0,800
Knob 3 FX Unit 2 Direct Mapped to ?? M1-2 ---- Button Direct FX Unit 2 0,900
Knob 3 FX Unit 2 Direct Mapped to ?? M1-3 ---- Button Direct FX Unit 2 1,000
Button 3 FX Unit 2 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 2 1
Button 3 FX Unit 2 Hold Mapped to ?? M1-4 ---- Button Hold FX Unit 2 ----
Effect 3 Selector FX Unit 2 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 2 Filter LFO
Effect 2 Selector FX Unit 3 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 3 Tranpose Stretch
FX Store Preset FX Unit 2 Trigger Mapped to ?? ---- ---- Button Trigger FX Unit 2
FX Store Preset FX Unit 3 Trigger Mapped to ?? ---- ---- Button Trigger FX Unit 3
FX Unit Mode Selector FX Unit 2 Direct Mapped to ?? ---- ---- Button Direct FX Unit 2 Group
FX Unit Mode Selector FX Unit 3 Direct Mapped to ?? ---- ---- Button Direct FX Unit 3 Group
Knob 2 FX Unit 3 Direct Mapped to ?? M1-0 ---- Button Direct FX Unit 3 1,000
Knob 2 FX Unit 3 Dec Mapped to ?? M1-4 ---- Button Dec FX Unit 3 Auto Repeat aanvinken
Button 2 FX Unit 3 Hold Mapped to ?? M1-3 ---- Button Hold FX Unit 3 —
Button 2 FX Unit 3 Hold Mapped to ?? M1-4 ---- Button Hold FX Unit 3 —
thx Mad
ps: Scamo is using FX 1 in group an FX 3 as Single, FX 2 in group and FX 4 as Single
also it activat FX 1 and FX3 on the left panel, FX 2 and FX 4 on the right side
Mapping is correct. That’s the reason why I have posted video - to prove it works.
[QUOTE]I inported your tsi, and it gives in Mapped to: Ch01.Note.C 1
I try to hit the button “Learn” in Traktor but it doesn’t work.[/QUOTE]
C1 is MIDI note for button that I have mapped this combo on my bcd3000. Make sure that you have set MIDI in and out ports to your controller in this mapping so Traktor can send and receive MIDI signal. I assume that both of ports are set to ‘none’ when you import it?
[QUOTE]I use the S4 and F1
I’m new at tsi files and try to analyse the tsi of Scamo.
can you give more info how to do this please.[/QUOTE]
I don’t have S4 (unfortunately) so I never check in to scamo’s mapping to see how all modifiers are set and eventually troubleshoot it for you. Only tip I can give to you is to take a look in to little modifier slots (1-8) where modifier values are displaying and find corresponding modifier conditions that you need to use in order to add any parameters into determined FX mode from scamo’s mapping.
[QUOTE]ps: Scamo is using FX 1 in group an FX 3 as Single, FX 2 in group and FX 4 as Single
also it activat FX 1 and FX3 on the left panel, FX 2 and FX 4 on the right side[/QUOTE]
I’m aware that every mode require one FX unit to be in group and second in single mode - got that from readings btw. In that case, you need to move Transpose effect in to same FX unit where Beatmasher slot is.
I made it to work (sort of),still trying to get it right like yours, but:
Why go in to group if you use only the Beatmasher in one slot?
If the Transpose and Beatmasher are in one slot (FX 1), like I did already, than I can go in group.
Idd for ports, I try everyting and still could use the learn key, don’t know why, so I made the mapping in Scamo’s map, I’ll ask if he will have a look if he hase time.
The Beatmasher and Transpose are in group FX mode because it leave opportunity to use other effects in combination with this supercombo. For example, I can engage Flanger or Reverb (or any) from same FX unit and still attach Masher+Trans to it.
