# Behringer DDM4000 Assembly

**URL:** <https://forum.djtechtools.com/t/behringer-ddm4000-assembly/65855>\
**Category:** Hardware: Controllers, Mods and Gear\
**Tags:** behringer-ddm4000\
**Created:** [May 2, 2014, 4:19pm UTC](https://forum.djtechtools.com/t/behringer-ddm4000-assembly/65855 "2014-05-02T16:19:36Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![SlickVikram](https://avatars.discourse-cdn.com/v4/letter/s/43a26b/32.png) [@SlickVikram](https://forum.djtechtools.com/u/SlickVikram)\
**Post date:** [May 2, 2014, 4:19pm UTC](https://forum.djtechtools.com/t/behringer-ddm4000-assembly/65855/1 "2014-05-02T16:19:36Z")

</div>

**Behringer DDM4000 Assembly**

Hello all, just took the cover off my Behringer DDM4000 and I’m having difficulty getting it back on properly. The outer panel goes back on just fine but I can’t seem to get the circuit board underneath to a high enough level, it just sags back down and I can’t figure out what it was that was holding it up to within a few centimeters of the outer panel. Has anyone ever had the same problem?  
Any input would be appreciated.  
Thank you

---

<div class="post-metadata">

**Author:** ![Sambo](https://avatars.discourse-cdn.com/v4/letter/s/ed655f/32.png) [@Sambo](https://forum.djtechtools.com/u/Sambo)\
**Post date:** [May 2, 2014, 5:04pm UTC](https://forum.djtechtools.com/t/behringer-ddm4000-assembly/65855/2 "2014-05-02T17:04:25Z")

</div>

Not opened one myself but perhaps the front panel was screwed on to the motherboard, therefore keeping it up?

---

<div class="post-metadata">

**Author:** ![031999](https://sea1.discourse-cdn.com/flex001/user_avatar/forum.djtechtools.com/031999/32/86_2.png) [@031999](https://forum.djtechtools.com/u/031999)\
**Post date:** [May 2, 2014, 9:58pm UTC](https://forum.djtechtools.com/t/behringer-ddm4000-assembly/65855/3 "2014-05-02T21:58:18Z")

</div>

look at this picture [http://www.behringer.com/assets/DDM4000\_P0167\_TopPers\_XL.png](http://www.behringer.com/assets/DDM4000_P0167_TopPers_XL.png)

there is quite a few screws in the faceplate, some of those got to be for holding up the knobs and stuff.

---

<div class="post-metadata">

**Author:** ![SlickVikram](https://avatars.discourse-cdn.com/v4/letter/s/43a26b/32.png) [@SlickVikram](https://forum.djtechtools.com/u/SlickVikram)\
**Post date:** [May 3, 2014, 3:31pm UTC](https://forum.djtechtools.com/t/behringer-ddm4000-assembly/65855/4 "2014-05-03T15:31:26Z")

</div>

That’s what I was thinking but I’m having a hard time trying to hold the circuit board at a high enough level to the main one so as to get a screw in. To place a screw in to the top board, it has to be placed flat on to the mixer, leaving the circuit board sagging down and well out of reach.