# Headphone Cue w AudioFire4 - Correct Config but still not working

**URL:** <https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440>\
**Category:** General Discussion\
**Created:** [November 26, 2008, 4:56am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440 "2008-11-26T04:56:00Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![ceezo66](https://sea1.discourse-cdn.com/flex001/user_avatar/forum.djtechtools.com/ceezo66/32/14329_2.png) [@ceezo66](https://forum.djtechtools.com/u/ceezo66)\
**Post date:** [November 26, 2008, 4:56am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/1 "2008-11-26T04:56:00Z")

</div>

**Headphone Cue w AudioFire4 - Correct Config but still not working**

From what I have gathered from the forum I have the correct setup but headphone cueing is still not working with me in traktor scratch pro.

Settings:

-Audio Device: ASIO AudioFire  
-Output Routing:

Mixing Mode: Internal

Output Monitor  
L 3: Analog out 3  
R 4: Analog out 4

Output Master  
L 1: Analog out 1  
R 2: Analog out 2

Input Routing: Everything set as “not connected”

Speakers and cross fading are working fine it’s just the headphone cueing that does not work.

Yes I read the manual and no help.

---

<div class="post-metadata">

**Author:** ![ceezo66](https://sea1.discourse-cdn.com/flex001/user_avatar/forum.djtechtools.com/ceezo66/32/14329_2.png) [@ceezo66](https://forum.djtechtools.com/u/ceezo66)\
**Post date:** [November 26, 2008, 5:03am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/2 "2008-11-26T05:03:02Z")

</div>

Note:

When I switch 1&2 with 3&4 and vice versa pressing the headphone cue button on my vci100se causes both my headphones and speakers to jump to full volume.

Also, with the above configuration, I hear the same thing from my speakers and headphones.

Connectivity:

Laptop headphone jack out to SPDIF input  
Computer speakers jack plugged into Audiofire Output 1  
Headphones plugged into headphone jack which is in the front of the Audiofire w the preamps

---

<div class="post-metadata">

**Author:** ![Mole](https://avatars.discourse-cdn.com/v4/letter/m/9fc348/32.png) [@Mole](https://forum.djtechtools.com/u/Mole)\
**Post date:** [November 26, 2008, 5:17am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/3 "2008-11-26T05:17:31Z")

</div>

I’m using an Audiofire 2 and headphone cueing works with traktor pro.

My settings in traktor

Output monitor L Playback 3  
R Playback 4

Output Master L Playback 1  
R Playback 2

Check your settings in audiofire console,

Playback 1 & 2 analog out  
Playback 3 & 4 Headphones

Why do you have Laptop headphone jack out to SPDIF input?

---

<div class="post-metadata">

**Author:** ![ceezo66](https://sea1.discourse-cdn.com/flex001/user_avatar/forum.djtechtools.com/ceezo66/32/14329_2.png) [@ceezo66](https://forum.djtechtools.com/u/ceezo66)\
**Post date:** [November 26, 2008, 6:34am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/4 "2008-11-26T06:34:40Z")

</div>

Hey Mole-

I opened the audiofire console and could not find the settings to specify analog out vs headphones. All I see is the green/yellow/red volume bars going up and down as the music plays. I think our traktor settings are the same so the problem must be in the audiofire console.

Also, if I do not connect my headhone jack out to SPDIF input how else am I supposed to get the music to the soundcard?

_noob alert_ 🙂

---

<div class="post-metadata">

**Author:** ![4nT1](https://sea1.discourse-cdn.com/flex001/user_avatar/forum.djtechtools.com/4nt1/32/16142_2.png) [@4nT1](https://forum.djtechtools.com/u/4nT1)\
**Post date:** [November 26, 2008, 7:33am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/5 "2008-11-26T07:33:25Z")

</div>

the music gets to the soundcard from the workstation/notebook via the firewire plus at the back.

the spdif out or 1/4 inch line outputs shoudl then go to your mixer or amp and then to speakers.

headphones would be plugged into a headphone jack - typically located at the front.. this is probably your problem if your pluggin them in the back

image can be found here \> [http://www.echoaudio.com/products/FireWire/AudioFire4/audiofire4\_both\_big.jpg](http://www.echoaudio.com/products/FireWire/AudioFire4/audiofire4_both_big.jpg)

make sure you have the phones volume turned up and plugged in to the 1/8 jack under the word phones.

hope that helps..

---

<div class="post-metadata">

**Author:** ![Mole](https://avatars.discourse-cdn.com/v4/letter/m/9fc348/32.png) [@Mole](https://forum.djtechtools.com/u/Mole)\
**Post date:** [November 26, 2008, 10:14am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/6 "2008-11-26T10:14:30Z")

</div>

The firewire connection to the audiofire is all you need, disconnect the spdif.

Here is the manual

[http://www.echoaudio.com/Downloads/Manuals/AudioFire%20Windows%20Manual%20v2.0.pdf](http://www.echoaudio.com/Downloads/Manuals/AudioFire%20Windows%20Manual%20v2.0.pdf)

According to that analog outputs 1 & 2 are monitored with headphones so you should set those in traktor as monitor and 3 & 4 as master.

Try the cue button in software first in case there’s something wrong with your midi settings.

You do have your channel fader at 0 when you cue right?, because you will hear the same thing through phones and speakers if you don’t.

BTW if your have only connected output 1 to your speakers thats a single channel so mono only.

---

<div class="post-metadata">

**Author:** ![djas](https://avatars.discourse-cdn.com/v4/letter/d/46a35a/32.png) [@djas](https://forum.djtechtools.com/u/djas)\
**Post date:** [November 27, 2008, 2:11pm UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/7 "2008-11-27T14:11:23Z")

</div>

Audio Device: Asio AudioFire  
Mixing Mode: Internal  
Monitor output: 1/2  
Master output: 3/4 or 5/6

---

<div class="post-metadata">

**Author:** ![ceezo66](https://sea1.discourse-cdn.com/flex001/user_avatar/forum.djtechtools.com/ceezo66/32/14329_2.png) [@ceezo66](https://forum.djtechtools.com/u/ceezo66)\
**Post date:** [November 29, 2008, 3:15am UTC](https://forum.djtechtools.com/t/headphone-cue-w-audiofire4-correct-config-but-still-not-working/1440/8 "2008-11-29T03:15:02Z")

</div>

> [@Mole](#):
>
> The firewire connection to the audiofire is all you need, disconnect the spdif.
> 
> Here is the manual
> 
> [http://www.echoaudio.com/Downloads/Manuals/AudioFire%20Windows%20Manual%20v2.0.pdf](http://www.echoaudio.com/Downloads/Manuals/AudioFire%20Windows%20Manual%20v2.0.pdf)
> 
> According to that analog outputs 1 & 2 are monitored with headphones so you should set those in traktor as monitor and 3 & 4 as master.
> 
> Try the cue button in software first in case there’s something wrong with your midi settings.
> 
> You do have your channel fader at 0 when you cue right?, because you will hear the same thing through phones and speakers if you don’t.
> 
> BTW if your have only connected output 1 to your speakers thats a single channel so mono only.

Thanks I disconnected the extraneous spdif cable.

I have the settings as it is written in the manual (monitored 1&2, master 3&4) and they give me the following result:

When Deck A channel fader is at zero (all the way down) and the cross fader is all the way right (so only Deck B is audible) when I press cue on the vci100se or in traktor pro I can suddenly hear Deck A louder than Deck B over the speakers and headphones even though it should be silenced over the speakers since the channel fader is at zero.

What am I doing wrong?

Mole mentioned to ensure my settings are:

Playback 1 & 2 analog out  
Playback 3 & 4 Headphones

But in my console for audiofire 4 I am not able to specify those settings. I simply have volume meters and under the settings tab I can only change sample rate, buffer size, clock source, and spdif format.

Any ideas?
