Hey folks, here is the latest version of my X1 Mapping, designed for those who wish to use the X1 as a mixer. Video is uploading.
Notes:
2 Modes, FX (Standard) & EQ (Mixer)
Crossfader can be used in any mode
Preparation functions
General tweaks
[FX ON]
Toggles FX/EQ Modes
Switching to EQ Mode engages filter, FX Mode disengages filter
SHIFT + [FX ON] resets Gain & Filter
[DRY/WET]
FX Mode: [DRY/WET] for FX Unit 1
EQ Mode: Filter Adjust SHIFT + [DRY/WET] Gain Adjust
[1-3]
FX Mode - Effects activate 1-3 SHIFT + [1-3] cycles the available effects.
EQ Mode - EQ Kill Low, Mid, High (also mid low/high if you use the Xone eq)
SHIFT + [1-3] in EQ Mode activates Effects 1-3 just as if you were in FX Mode
Removed FX Unit 1&2 Kill when swapping modes, due to “customer feedback”
Right [BROWSE] is normal playlist scrolling
Left [BROWSE] switches to browser mode as well as normal scrolling
Loading either deck switches back to deck view
SHIFT + [LOAD] toggles between Deck/Browser views
SHIFT + [BROWSE] scrubs through the track
In EQ Mode, [FX1] & [FX2] are volume controls, with some led feedback (Full volume bright, low volume dim)
Crossfader:
Works in any mode
SHIFT + Left [FX1] & Right [FX2] activates the Crossfader
SHIFT + Left [FX1] & Right [FX1] activates the Auto XF
SHIFT + Left [LOOP SIZE]
Beatjump on focus deck (+/- 32)
SHIFT + Right [LOOP SIZE]
Deck Zoom In/Out
SHIFT + Left [IN/OUT]
Move Grid
SHIFT + Left [TEMPO BEND +/-]
Adjust Analyzed BPM
SHIFT + [Sync]
Drop Grid Marker
SHIFT + [CUE] + [CUP]
Previous/ Next Cue point
Also some miscellaneous features mentioned in coming video
ADDED - Switching deck to FX mode now resets filter position
Loading deck resets deck zoom to -.75 (default position)
Loading deck resets crossfader to centre position
Loading deck in Mixer Mode makes deck volume 0 (the idea being if you use the FX mode when you prep tracks, the deck volume stays up making things a bit easier)
SHIFT + PLAY toggles BPM lock on/off
In the zoomed preparation mode, tempo bend can be used to fine tune the playhead position before
dropping a grid marker
I am a little bit confused about switching presets. It says to place both FX1 and FX2 (the top buttons) to ON to go into mixing mode. This works but when I turn them off to get out of mixing mode, the FXs turn off. Is there a way to switch with a shift button so that I can still keep FXs on in either FX or mixing mode?
Hi there,
the modes are independent for each deck so you could have deck a in mixer mode and deck b in fx mode, for example.
the fx units remain on when switching between modes if you have them set, and you can still activate the effects by holding shift+1-3 kill.
what traktor version are you on? i haven’t been able to replicate your problem, this mapping was made in tsp 2.5.1, if you are using 2.6+ there have been more changes to the way mappings work which i haven’t tested.
One thing that may not be troubleshootable: when you switch to FX mode it cuts the fillter but also disables shift+dry wet for Gain. When you turn EQ mode on it enables the filter and the second you touch the dry-wet it’ll move the filter knob to the point of the gain you have set. So if you run with the Gain on +5 or what not then your filter is going to kick in.
I know it’s probably not possible, or if it is to map it to another, but is it possible to smoothe out how those two FX ons work so that you can always control them to their full extent? I have no problem manually moving the gain to what it should be set as but if I have the filter off I can’t move the gain at all.
