Traktor Pro Layout ‘Hack’ for 13inch Macbook & 2 Decks [UPDATED with video]
### Please read this post for an easier, updated method to do this ###
Traktor Layout 'Hack' for 13inch Macbook & 2 Decks - General Discussion - DJ TechTools Forum
Just a few points:
- will work on OSX 10.8 now!
- NI fixed the waveform bug on large displays with 2.5, so it will work with a 15inch, 17inch model now
- should work the same way on windows (i have no way to try at the moment)
Old post, ignore these instructions:
Hi guys,
I have been a long time reader of the forum but this is my first post. I have discovered a way to trick Traktor and MacOSX so you can alter the layout which is very useful for my setup. This would only be useful for you if you use 2 Decks and 2 FX units. It will hide some information, but give you much better overview of your two tracks in return (you will lose the sample decks and internal crossfader for example).
Since some of you asked, here is a video of it in action (this is not about mixing!):
You will basically have to use Deck A&C as Deck A&B and FX1&3 as FX1&2. Also you will have to toogle between Browser View and Deck View using the spacebar.
INSTRUCTIONS
Important information & How to revert back to normal
■ Due to a bug in Traktor 2 at high resolutions it is not wise to make the waveform wider than in the example image above. It would make the stripeview unusable. That’s why it is a good idea to display the internal mixer & filter sections even if you are mixing externally. In Traktor Pro 1 you can fill the whole screen or a bigger display with the waveform.
■ You only have to do these steps once, as long as you never press the little plus button in the titlebar - if you need to see all decks you can switch to fullscren and back → it should remember your layout
■ If you want to revert back to normal simply click the little green + button (or grey in my case) in the upper left corner. To show the menubar simply move your cursor to the top of the screen. To reset the menubar delete the two lines from step #2.
1# Preparation
■ Setup your traktor layout similar to mine (4 FX, 4 Decks, hide Crossfader…).
■ be sure to have your master set right & close Traktor
2# Hide the Menubar (this will only affect Traktor, not other programs!)
■ Go to Programs → Native Instruments → Traktor (2)
■ right click (or CTRL+click) on the Traktor Icon and choose Show Package Contents
■ open Contents → open the info.plist with an editor
■ scroll down to the very bottom, it will look like this
...
<key>LSPrefersCarbon</key>
<true/>
</dict>
</plist>
■ now add the following two lines, so it looks like this
...
<key>LSPrefersCarbon</key>
<true/>
[B] <key>LSUIPresentationMode</key>
<integer>4</integer>[/B]
</dict>
</plist>
■ save & close
3# Enlarge Layout
■ open Terminal (open Spotlight & type Terminal)
■ paste the following code and press enter
defaults write com.native-instruments.Traktor AppleDisplayScaleFactor 0.5
■ open Traktor → it should be half the size & look like this (don’t freak out!)
■ drag the window to the upper left corner and resize it to this size
■ make sure the Browser columns are resized to roughly half of the windows width
■ close Traktor
■ open Terminal, paste the following code & hit enter
defaults write com.native-instruments.Traktor AppleDisplayScaleFactor 1.0
■ open Traktor again → done!
■ the layout might not be perfect yet, you may have to repeat step 3 and play around with the window size till you get it right…maybe you want to make it a bit smaller so you can see the master output
■ be sure to check the stripeview in Traktor Pro 2, if it’s not working correctly your waveform is too wide!
4# 4 Decks
■ If you or I find a tool to set the X and Y position of the window with a keyboard shortcut or MIDI command, it would be possible to switch between Deck A&C and Deck B&D and use all four decks this way
Hope some will find this useful!
