Printable View
Hello guys, i have a Behringer NOX 404 and i recently purchased a Traktor Audio 2 sound card to perform with its software. However,given that im not an expert of audio routing,i can not make my mixer work. Please help me out . Also the Traktor pro setting seems to look like a havoc that i cant relate with any of the "how to " videos out there.
thanks \\
Attachment 24028Attachment 24029
Skip to around 1:20. Each output of the Audio 2 (using AUX to RCA cables) goes to a separate LINE input on your mixer.
https://www.youtube.com/watch?v=uj_Afs3y5_Y#t=110
Hello , thank you for replying . I actually referred to the video and lay it out as i should..But still nothingQuote:
Originally Posted by padi_04
for my understanding .
Audio 2 (Main) Taktor Sound Card ---> Channel One (Input 1, LINE )
Headphone Symbol on Traktor sound Card ---> Channel two (Input 2,Line)
Then,
Main Out Put (RCV ) goes as a 3.5mm jack to my speaker system
Thats the correct routing i believe .
Traktor Pro 2 Settings are the same as video
i still can not get a signal on crossfader indicating that a song is playing.
When turn on the mixer ,the power is coming through since there are little LEDs brighten up. Do you think there is a fault in the mixer?
Thanks again.
Did you make sure that the volume knobs on the Audio 2 were up, gains were up on the mixer and input source selected as line?
The button on the back of that mixer + the switch on the top must have line selected. make sure you are in EXTERNAL mixing mode, have the audio 2 selected as the audio source, your jack< rca's are plugged in to the line inputs, not phono + your output routings are set to 1/2 + 3/4 (or similar) .. also kinda obvious but check the gain knobs, if they are fully left then duh....
Hit us back if you still have problems.
Honestly i checked evrything over 10 timesQuote:
Originally Posted by Jester
the volumes
the knobs
line inputs
external mixing mode
the latest update : seems like i can play a song on deck A and get a song playing in the mixer but the both mixers have somewhat control over it. It seems like when i bring the fader down on channel B ,the song on deck A gets louder.
is it the traktor version im using? the new Yosimite update? i must be missing something.
all checked. however deck A could audible eventhough it has no control from the mixer.And the deck B doesnt make a sound ,but it could control somewhat deck A is playing. random things are working,Quote:
Originally Posted by Jester
This is correct. Make sure the Phono/Line button on the mixer (by the Input jacks) are pressed down - if they are up, the mixer will be looking for input on the Phono jacks, which use a different type of signal (so don't connect the Audio 2 to the Phono jacks).Quote:
Originally Posted by Spacefunk
You probably should be using the XLR outputs (the big jacks with the 3 pins inside) with a pair of "microphone" cables to connect the mixer to your speakers.Quote:
Main Out Put (RCV ) goes as a 3.5mm jack to my speaker system.
As Jester said, you also need to have Traktor's settings correct, so that Traktor knows it should be sending signals to the Audio 2, and which configuration to use.
If you go into Preferences in Traktor, and go to Audio Setup, the Audio Device should be the Traktor Audio 2.
Then, on the Output Routing page, Mixing Mode should have External selected, Output Monitor should have something like "Traktor Audio 2 - 3 & 4", and Output Master should have something like "Traktor Audio 2 - 1 & 2".
Play some music in Traktor, and bring up the faders on the mixer and see what happens.
Quote:
Originally Posted by DJTroyT
im certain, i had it checked with one of my friends too.Unless there is a problem with my Main audio Out from the mixer. And chek out the picture,is it possible for it to behave like this.the both faders are down and channel two has some kinda connection with channel one.
Attachment 24039
I've been lurking to try and figure it out. Everything seems like it should work, but I just noticed this.Quote:
Originally Posted by Spacefunk
There are some issues with Yosemite. There is apparently an incompatibility between Avid's drivers and NI's. So, if you have any avid software (e.g., pro tools, venue, media composer) installed....there are issues. There was also one described more recently that affected several sound cards (though not the Audio 2).
It very well might be a Yosemite issue. Go ahead and see if there are driver or firmware updates for your A2 (drivers are in service center; you'd have to google for firmware updates, I've never had to do one). And if you're on 2.7.0, upgrade to 2.7.1.
One other thing that you seem to have said is that "both mixers" do something to the audio. Traktor's mixer shouldn't have faders if it's in external mode. The EQs, gains, filters, and key knobs all still work. So does the master output knob. Double-click each one to reset it to default, and make sure the EQ kill buttons (little blue lights) are off.
What was traktor doing when that picture was taken?Quote:
Originally Posted by Spacefunk
The only thing I see "wrong" on the face of the mixer is that the effects loop is set to wet. It probably shoulnd't be. That meter mode ("mono 1/2") should be showing the pre-fader level of each of the 2 channels. So if the same thing was playing on both channels, that's exactly what it should look like. If anything was playing on both channels, it could look like that by coincidence.
So...here's what I'd do.
You have a cable with a pair of RCAs on one side and a stereo mini (headphone) plug on the other. Plug it into your laptop's headphone jack and the mixer's channel 1. Make sure your laptop volume is up (2/3 to full) and play some music (iTunes or youtube is fine; don't bother with traktor for this). See if it shows up on the meter, see if you can hear it in the headphones. If you can, try it again on channel 2. If that also shows up on the meter and in your headphones, switch the meter source to "stereo house" and play with the channel faders, crossfader, and master output. Do they seem to look like they should?
If that all goes well, it's fairly safe to say the mixer probably works. Behringer has made some absolute garbage in the past, but the nox mixers are supposed to be alright.
Next, plug in the Audio 2 via USB to your computer. Plug your headphones into The A2's master output. Open the Audio preferences and select the Audio 2 as your computer's output device. Turn the A2's volume for that output all the way down and play some audio (again...iTunes, youtube, etc., not traktor). You shouldn't hear anything. Turn it's volume up and see if you hear things.
Open Audio Midi Preferences (I don't know where it is, use spotlight to find it), and use it's speaker controls to select the other output (assuming the Audio 2 drivers will let you). Same story....volume down, itunes, volume up.
If that all works, the A2 is probably fine. My guess is that it'll fail somewhere in there.
Then...basically do it again with Traktor. Start with the Audio 2 as your device on INTERNAL mixing mode. 1/2 for master out, 3/4 for monitor out. Play with traktor's internal mixer and see if both outputs work as they should.
Then try it again in EXTERNAL mode. deck a: 1/2, deck b: 3/4, plugged into the mixer's line inputs, with it set the way you have it in that picture, but with the FX Loop control set to DRY.
If it works, awesome. If not, let us know where it failed.
If it's a yosemite problem, the mixer should work, and it should be weird when you use the audio 2 with iTunes, but it won't necessarily completely fail.
If it's a mixer problem, the mixer will keep being weird, but the Audio 2 will work with iTunes and traktor internal.
If it's a Traktor issue, everything will work except traktor.
If nothing works....you probably have a lemon mixer and either a yosemite issue or a lemon audio 2. Or you're only using bad cables. Or you're missing some piece of the instructions that you'll probably kick yourself for when you figure it out.
And yes, if that's the case...we'll probably make fun of you and then immeidately switch to telling stories about boneheaded things we've all done....like the time I traded out every single cable only to realize days later that I forgot to plug the mixer into the power strip and didn't notice that it's power light never came on.
hey man,thank you very much for all the information. I tried everything out and came to a conclusion.Quote:
Originally Posted by mostapha
as you said i checked the faulty of Traktor Audio 2 and it turned out to be fine. i have 2 of them so either has to be fine.so i ruled it out.
When checking the mixer channel 1 turned out to be fine and Channel 2 fader was working the otherway around. (when i turn down the fader volume increases)
so there is that
and tracktor seems to be completely fine.
There is no firmware update for A2 ,so in conclusion it come backs to yosimite update. i read this forum and NI forums and i came across this which could be the solution.
https://discussions.apple.com/thread/6623697
it seems much work ,should i go for a technician or do it by myself. (i cant afford to screw it up lol )
check the native instruments sight. I think the old A2 could be connected to each channel of a two channel mixer but the new one cant. if you want to mix with your lap top and a mixer you have to get a A6 if you are using traktor pro 2. honestly you should return the A2.
Resetting SMC and PRAM is safe and a fairly normal debugging step for Apples. If something goes wrong, it indicates bigger failures. That being said, I don't see how it would solve the problem unless I'm missing something. .Quote:
Originally Posted by Spacefunk
So, what you're getting is that Traktor works, that the A2 works, that channel 1 on the mixer works, and that channel 2 works with the fader running backwards?
Is the fader reverse switch pressed in on the right side of the mixer?
This is incorrect. Here is the current layout diagram for the A2 for external:Quote:
Originally Posted by dj max bradley
http://express-ec.native-instruments...2440cb06-d.jpg
This is wrong.Quote:
Originally Posted by dj max bradley
I think I am right the new A2 does not connect to a mixer. you can find out in the native instruments web sight. im not saying I am entirely sure.Quote:
Originally Posted by mostapha
Youre %100 wrong, as per the picture I linked above.Quote:
Originally Posted by dj max bradley
sorry for annoying you so much. is there only one stereo out on the A2 meaning one channel of your mixer
Youre not annoying me at all. You are just incorrect. Did you even look at the diagram?Quote:
Originally Posted by dj max bradley
There are two stereo outs including the headphones. You route channel 1 to the main output, channel 2 to the headphone output, and use the mixers headphone system for cueing, and the mixers speaker outputs for your final speaker output.
ohhhhh so it can mix internally and externally with both channels on your mixer? is the nox 404 any good. I nearly got a nox 1010 and someone bought me a pioneer DJM 800. the DJM is great its actually a club mixer. I recommend you get the XLR cords they sound better and look cool!
we worked it out I did not realise the headphone jack on the A2 could be used as a mixer channel.Quote:
Originally Posted by mostapha
Lols, that information was in the first 3 posts of the thread.Quote:
Originally Posted by dj max bradley
Hello team, I have a new set up that I can work pretty good from my lap top and small desk speakers, but now everyone wants me to DJ their small parties and receptions. I need help putting all of the stuff that I have together. I have the laptop with DJUCING on it. I have a 1000 watt amp, two 1200 watt speakers and 1 1000w woofe and a Hercules DJ air mixer. HOW DOES ALL OF THIS GO TOGETHER. I have one speaker insert from the mixer with another insert for headphones. Please give me the play by play to put this all together. You can email me at vertjr2@yahoo.com also.