VCI-100SE v4 Mapping for Traktor Pro 2

[rd0360]

@klaemo - Thanks bud, that's why it wasn't jumping out at me initially I'll take a look at it tomorrow.

Just realised someting that has been puzzling me with the tempo of the samples, in the sample decks. I exposed the master clock, and noticed the track deck which is highlighted as master, could be dependent on the position of the channel faders, and the cross fader.

e.g.
track deck A could have a track 127bpm, and not be playing.
track deck B could have a track loaded at 110 bpm, and be playing.
track deck D could have a sample loaded (from deck B), and be playing at a noticeably higher tempo than deck B (namely at 127bpm!). Even if it was set in loop mode, where the documentation says it should be synced. Tried the phase sync, and obv this didnt help, as it is phase not tempo.

Then I realised, that either a function of the mapping (or trakor generally) as I was just playing at home, and not performing, my faders were on the side of deck A, and there was mismatch somehow between the software and hardware positions, so Deck A had been set to master (even though deck was stopped).

This had me scratching my head for a while, as it there seemed to be no logical reason why sometimes the tempo of the samples would be correct, and sometimes seemingly fucked up. Anyhow, I am sure most of you know this already, but if this switches on the lightbulb for someone, then it was worth it.

Cheers,

Ry

[tuckerdgreat]

hi i have the new overlay as well can u tell me where did u excatly get the tsi file for that....theres so much stuff on this site..the ones ive tried doesnt seem to work...aslo ..did u have to got thru the set up wizard?....
thanks

[gonekrazy3000]

@tuckerdgreat:- already responded to you before. go here:- http://forum.djtechtools.com/showthr...l=1#post456581

[GUVNA]

Ive had an major issue with the dedicated echo button.If i have samples playing in deck 4, then use the echo button, it changes the tempo by half on the samples.Then when i push sync to correct it on deck 4 it plays them too fast, a 3rd press actually syncs them again.
I found that if i stop the samples before releasing the echo button it doesnt happen and i can start them synced fine.But the whole bug comes from the samples still playing when you release that button.If it happens pressing the echo button re-syncs them for the time it is pressed also.

Hope i explained this ok, i could throw up a video on youtube.

[Golden Ears]

I can download it but it will not import into Traktor Pro 2 for me... odd since my EGE VCI-400 mapped easily... but something must be different with the VCI-100SE Arcade. I have version 1.4 firmware..and was able to use the VCI_100SE v3 upgrade. I am using Traktor Pro 2 2.13 with a VCI-100SE Arcade VCI firmware 1.4

I tried importing it twice, and even did a full reboot and restart..nothing last 2 days.

[flashflooder]

i am unable to use the jogwheels as previously to scratch with ? now when i touch the platter the playing tune just stops?

you need to be running at least traktor 2.1 or higher. otherwise you likely do not have 1.4 fw on your vci-100.

[flashflooder]

I can download it but it will not import into Traktor Pro 2 for me... odd since my EGE VCI-400 mapped easily... but something must be different with the VCI-100SE Arcade. I have version 1.4 firmware..and was able to use the VCI_100SE v3 upgrade. I am using Traktor Pro 2 2.13 with a VCI-100SE Arcade VCI firmware 1.4

I tried importing it twice, and even did a full reboot and restart..nothing last 2 days.

i just tested downloading (from the first post on this thread) and importing the mapping into traktorn and it worked fine for me. try downloading the file and importing again and let me know if you still have the issue.

[flashflooder]

hi i have the new overlay as well can u tell me where did u excatly get the tsi file for that....theres so much stuff on this site..the ones ive tried doesnt seem to work...aslo ..did u have to got thru the set up wizard?....
thanks

try this link for the v4 (new overlay) mapping: http://maps.djtechtools.com/mappings/1 and no you do not have to go through the set up wizard, just import using the button on the bottom left of the preferences section

[Golden Ears]

i just tested downloading (from the first post on this thread) and importing the mapping into traktorn and it worked fine for me. try downloading the file and importing again and let me know if you still have the issue.

I did that.. and still nothing..very odd. Hmmm maybe I only have version 1.3 of the firmware... is there a V4 version that uses 1.3 firmware? That I could test? I sent it to DJTT about 2 years ago for a firmware upgrade since I did not have a serial port. Don't remember if that was version 1.3 or 1.4 now that I think about it

[Golden Ears]

Actually I am about 90% positive I have firmware 1.4 because I remember I wanted the higher resolution jog wheels. -what is the way to tell what you have?