Kontol X1 owners. Do you have faulty FX knobs too?
Results 1 to 9 of 9
  1. #1
    Tech Guru space monkey's Avatar
    Join Date
    Mar 2009
    Location
    back home
    Posts
    1,174

    Default Kontrol X1 owners. Do you have faulty FX knobs too?

    Last week I had read on the NI forums where a few others had an issue with the FX knobs that worked well until ~75% rotation and stopped sending data until ~85%. This fault causes erratic behavior w/in Traktor's FX. Lo and behold, as this was the first thing I checked today, the same issue exists on my unit. Pretty disappointed as the unit would be perfect for me when I go overseas and was actually looking at purchasing another. Had I not read about the issue the fault may not have been detected for a little while as i'm not an FX genie.

    Just curious if anyone else has the same problem or perhaps not even noticed it.
    Last edited by space monkey; 09-16-2010 at 12:39 AM.

  2. #2
    DJTT Moderator Dude Jester's Avatar
    Join Date
    Feb 2009
    Location
    Noiseeland
    Posts
    12,426

    Default

    No problems here mate.
    Acer E5 i7 16GB 512SSD 2TBHD ~ WIN 10 ~ TSP 2.11 ~ AUDIO 6 ~ DUAL X1s ~ DN-X1600 ~ SPECTRA ~ TWISTER ~ ATH-PRO500 MK2 ~ ZED6FX ~ AT2020

    " I’m the Dude, so that’s what you call me. That or, uh His Dudeness, or uh Duder, or El Duderino, if you’re not into the whole brevity thing. "

  3. #3
    Tech Guru bumtsch's Avatar
    Join Date
    Sep 2009
    Location
    Paris, France
    Posts
    1,178

    Default

    My A+B X1 has jittery effects knobs unless they're all at 100%. No gaps but past a certain point they start sending a bit of unsolicited, around-the-current-value data.
    I think it's starting to spread to the collection browsing knobs. I can see the selected track jump sometimes.
    It was ok to use but after talking to NI support about other issues I think I'll finally have it replaced.

    No problems on my C+D X1

  4. #4
    Tech Mentor oskars's Avatar
    Join Date
    Jul 2010
    Location
    Stockholm
    Posts
    140

    Default

    When all my effect knobs but one are at 100% the last knob will make ALL THE OTHER knobs jitter at about 80% when I touch it.

    Very wierd.

  5. #5
    Tech Guru space monkey's Avatar
    Join Date
    Mar 2009
    Location
    back home
    Posts
    1,174

    Default

    Yeah, as for the jittery FX, I get slight movement on parameter 3 when moving parameter knob 2 at ~50% on FX unit 1 (advanced mode). This is troubling, haven't had the X1 for 12 hours and i'm boxing it back up for a refund. I get the feeling this is a common problem and if it is widespread doesn't bode well for the more complex, highly anticipated S4 controller. I'm not casting aspersions on NI but a basic QA/QC should detect faults like this.

  6. #6
    Tech Guru space monkey's Avatar
    Join Date
    Mar 2009
    Location
    back home
    Posts
    1,174

    Default

    @ oskars

    Did you ever receive your replacement? I submitted a ticket to NI 3 days ago and have yet to get a response other than the autorespond with ticket number.

  7. #7
    DJTT Dominator JesC's Avatar
    Join Date
    May 2008
    Location
    127.0.0.1
    Posts
    5,611

    Default

    Guys have you tried to recalibrate the unit? you can achieve this by going to the setup, then the kontrol x1 click on recalibrate and its going to ask move all the knobs to the left, center, right. and that should do the trick. my x1 was actiing up and this was that fixed that worked for me.
    Controllerist: Think different | SoundCloud | MixCloud | Twitter |

  8. #8
    Tech Guru space monkey's Avatar
    Join Date
    Mar 2009
    Location
    back home
    Posts
    1,174

    Default

    Yeah, recal does not work. I've monitored the midi signal in midiox and no signal is sent ~75% rotation. Also some signal seems to "bleed" into other CC causing them to jitter. This is obviously a fault and a good number of others have the same issue.


    EDIT:
    One thing is the behavior is dependent on what value each CC is at. For instance, If all CC are at 0 I am able to turn one CC w/o any jitter. If some CC are not at 0 and I turn Dry/Wet CC parameter 3 jumps around. If all CC are at 50% (centered) Dry/Wet sticks at 75% and jumps to 85%. CC midi values in this controller are somehow getting crossed by perhaps a bad board/chip or software.
    Last edited by space monkey; 09-17-2010 at 01:17 PM.

  9. #9

    Default

    Hopefully this wont be an issue with the s4

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •